Troy-bilt 42012 Manual do Utilizador

Models 42010 - 8 HP, 24" Auger42030 - 8 HP, 24" Auger42012 - 10 HP, 26" Auger42031 - 10 HP, 26" AugerOwner/OperatorManualSnowthrow

10Section 2: Assembly F. Install Discharge Chute 1. Remove the cardboard packing shieldfrom the discharge chute mountopening.2. Loosen (do not remove

11Section 2: Assembly Fig. 2-7YFig. 2-8AHACADABAAATASAGRAFAE5. Rotate the chute control crank (Z, Fig.2-6). The deflector chute should turnfreely.

12Section 2: AssemblyFig. 2-9AFABYellowYellow &Red WiresALAOANAMAKBlackBlackBlueRedFig. 2-10I. Attach Wheel Drive Control Rod1. Remove the plasti

13Section 2: AssemblyK. Wiring Harness Installation1. Remove the plastic cable tie thatsecures the wiring harness to the righthandlebar.2. Route the

14ControlsThis section defines the various controlson the unit. Refer to the following section,“Operation,” for an explanation of theproper use of th

15Section 3: ControlsH, Fig. 3-4—ThrottleLocated on back left corner of the engine,the throttle controls the speed of theengine. For proper operatio

Operation16Pre-operation checklist1. Review Section 1, “Safety” andSection 3, “Controls” in this manual.2. Check the unit for any loose ormissing hard

17Section 4: Operation Fill the fuel tank with fresh, cleanunleaded gasoline with a minimumoctane rating of 87. Leave 1/2" ofspace for fuel exp

18Starting the engine1. Review the “Pre-operation checklist”earlier in this section. Move the unitoutside to a well-ventilated, level area.2. Move th

19Auger drive engagement1. Remove any debris from inside theauger housing.2. Adjust the discharge chute deflectorcap (RR, Fig. 4-6) angle withadjustme

2Dear Owner:Thank you for purchasing this product. The unitwas carefully designed and manufactured toprovide excellent performance if properlyoperat

20Section 4: OperationTransporting the unitRelease the auger drive control lever todisengage the auger drive whenever theunit is being transported to

Maintenance21Engine oilCheck the engine oil level each time beforestarting the unit and after each 5 hours ofoperation. To check the engine oil level:

22Section 5: MaintenanceLubricationAt the beginning and end of each seasonor after every 25 hours of operation,lubricate the unit as recommended belo

length of spring (W, Fig. 5-6) again.The spring length should now measure5/8" – 3/4" (15–19mm) longer than themeasurement taken in step 2.

24Auger Drive Belt AdjustmentDue to wear, the auger drive belt maybegin to slip when the auger drive lever isengaged. To adjust the auger drive belt:1

25Section 5: Maintenance 5. Remove the auger drive belt from thelower drive pulley (AO).6. Remove the belt from unit.To install the auger drive belt:

26Section 5: MaintenanceBrake Arm AdjustmentThe brake arm adjustment is set at thefactory to 1/16 - 1/8” for proper belt/brakeclearance. Due to wear

27Section 5: Maintenance POSSIBLE PROBLEMIgnition key in STOP positionChoke knob in incorrect position Engine throttle lever in incorrect startingpos

28Section 5: MaintenanceTROUBLEAuger drive control lever does not engage auger driveAuger spins with drive lever disengagedWheel drive control lever

29Section 5: Maintenance IntervalBefore each useAfter each useEvery 25 hours of operationor annuallyEvery 50 hours of operationor annuallyAnnuallyIte

3Table of ContentsSECTION 1: SAFETY ... 4Safety Decals ...

30SpecificationsSnowthrower Models 42010, 42012, 42030, & 42031SnowthrowerHeight...To top of handlebar levers: 41.5" (105

31SpecificationsWiring DiagramDIODE/RECTIFIERENGINECONNECTORREDBLUEIGNITIONSWITCHHANDLEBARHEATERHANDLEBARHEATERGROUND TOHANDLEBARBLACKTo Light(optiona

For customer assistance, contact your nearest authorized dealer or:GARDEN WAY INCORPORATED • 1 Garden Way • Troy, New York U.S.A. 12180Customer S

Training1. Read this owner/operator manual andthe separate engine owner manualcarefully before operating the unit. Becompletely familiar with the con

5Section 1: Safety 3. Before starting the engine, check thetightness of all screws, nuts, bolts,and other fasteners. Replace or cleanany damaged o

611. Before inspecting the unit or makingany adjustments, or if the unit jams orbecomes clogged, shut the engine offimmediately and allow all movingp

7Section 1: Safety 5. Allow the engine to cool before storingin any enclosure.6. Store gasoline in a cool, well-ventilated area, safely away from any

Assembly8Section2IMPORTANT: Follow the assembly stepscarefully. Contact the factory or yourlocal authorized dealer if you have anyquestions or proble

9Section 2: Assembly AJBCEFDGHIIMPORTANT: Left and right sides of theunit are determined from the operatorposition, facing the direction of forwardtr