Troy-bilt TB90BC Manual do Utilizador descarregar pdf (Página 4)

RULES FOR SAFE OPERATION

• Wear heavy, long pants, boots, gloves and a long

sleeve shirt. Do not wear loose clothing, jewelry, short

pants, sandals or go barefoot. Secure hair above

shoulder level.

• The cutting attachment shield must always be in place

while operating the unit. Do not operate unit without

both trimming lines extended, and the proper line

installed. Do not extend the trimming line beyond the

length of the shield.

• This unit has a clutch. The cutting attachment remains

stationary when the engine is idling. If it does not, have

the unit adjusted by an authorized service technician.

• Adjust the J-Handle to your size to provide the best

grip.

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position

whenever pulling the starter rope. The operator and

unit must be in a stable position while starting. See

Starting/Stopping Instructions.

• Use the right tool. Only use this tool for the purpose

intended.

• Do not overreach. Always keep proper footing and

balance.

• Always hold the unit with both hands when operating.

Keep a firm grip on both the front and rear handle or

grips.

• Keep hands, face, and feet at a distance from all

moving parts. Do not touch or try to stop the cutting

attachment when it is rotating.

• Do not touch the engine, gear housing or muffler.

These parts get extremely hot from operation. When

turned off they remain hot for a short time.

• Do not operate the engine faster than the speed

needed to cut, trim or edge. Do not run the engine at

high speed when not cutting.

• Always stop the engine when cutting is delayed or

when walking from one cutting location to another.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Do not operate before repairing damage. Do

not operate the unit with loose or damaged parts.

• Stop and switch the engine to off for maintenance,

repair, or for changing the cutting attachment or other

attachments.

• Use only genuine manufacturer’s replacement parts and

accessories for this unit. These are available from

your authorized service dealer. Use of any non Troy-Bilt

LLC parts or accessories could lead to serious injury to

the user, or damage to the unit, and void your warranty.

• Keep unit clean of vegetation and other materials.

They may become lodged between the cutting

attachment and shield.

• To reduce fire hazard, replace faulty muffler and spark

arrestor, keep the engine and muffler free from grass,

leaves, excessive grease or carbon build up.

WHILE OPERATING WITH CUTTING BLADE

• Read and understand all safety warnings before

operating this unit.

• Always use the shoulder harness when using the

brush blade accessory.

• Keep the J-handle between the operator and cutting

attachment or blade at all times.

• NEVER cut with the cutting blade located over 30

inches (76 cm) or more above the ground level.

• Blade thrust may occur when the spinning blade

contacts an object that it does not immediately cut.

Blade thrust can be violent enough to cause the unit

and/or operator to be propelled in any direction , and

possibly lose control of the unit. Blade thrust can

occur without warning if the blade snags, stalls or

binds. This is more likely to occur in areas where it is

difficult to see the material being cut.

• For operation with the brush blade, do not cut

anything thicker than 1/2 inch or a violent kickback

could occur.

• Do not attempt to touch or stop the blade when it is

rotating.

•A coasting blade can cause injury while it continues to

spin after the engine is stopped or the throttle trigger

is released. Maintain proper control until the blade has

completely stopped rotating.

• Do not run the unit at high speed when not cutting.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Have any damage repaired before attempting

further operations. Do not operate unit with a bent,

cracked or dull blade. Discard blades that are bent,

warped, cracked or broken.

• Do not sharpen the cutting blade. Sharpening the

blade can cause the blade tip to break off while in use.

This can result in severe personal injury. Replace the

blade.

• Do not use the cutting blade for edging or as an

edger, severe personal injury to yourself or others can

occur. Use the cutting blade only for the purpose as

described in this manual.

• Stop the engine IMMEDIATELY if you feel excessive

vibration. Vibration is a sign of trouble. Inspect

thoroughly for loose nuts, bolts or damage before

continuing. Repair or replace affected parts as

necessary.

AFTER USE

• Clean cutting blades with a household cleaner to

remove any gum buildup. Oil the blade with machine

oil to prevent rust.

• Lock up and store the cutting blade in an appropriate

area to protect the blade from unauthorized use or

damage.

1 2 3 4 5 6 7 8 9 ... 83 84

Comentários a estes Manuais

Sem comentários

Troy-bilt TB90BC Manual do Utilizador Página 4

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento de jardinagem Troy-bilt TB90BC